PING IP ADDRESS

  • Home
  • IP Address
  • Blog

10.1.10.1 – Router Network IP Address

June 30, 2020 by Khalil Leave a Comment

10.1.10.1 The IP address of 10.1.10.1 login is relevant as it allows you to log in to your Comcast Business Router to set it up and control it. If you want to protect your router, set up a wireless network or a Guest network, this IP is what you need. The login steps for the Comcast business router mentioned in this article can be extended to a Cisco Business Wireless gateway:

10.1.10.1

 

10.1.10.1:

Table of Contents Show
10.1.10.1:
The application of 10.1.10.1:
Guidelines for login at IP address 10.1.10.1
Connect to your network:
Frequently Asked Questions about 10.1.10.1 login:
Common issues during the use of 10.1.10.1:
10.1.10.1 isn’t working:
10.1.10.1 timed out or refused to connect:
What should I do to set a port?
Conclusion:

10.1.10.1 may only be used by one computer in the network. Otherwise, a so-called Network dispute may arise when there are two machines using the same Protocol. This can have a poor effect or even make it unusable on your network.

The application of 10.1.10.1:

The default router Port, for example 192.168.1.1 or 192.168.0.1, is used to allow the user to access the router settings just like most default IP addresses. From there the user can control the router settings and allow, disable or change the many features that the router has to offer, such as:

  1. Shift Address on the router.
  2. Shift password on the router.
  3. Adjust the name of your wireless network (SSID).
  4. Set up or change the password for Wireless.
  5. Set up network of Visitors.
  6. Establish parental controls over your home network.
  7. However, you need to learn the 10.1.10.1 authentication step to do all of these acts.

10.1.10.1

Guidelines for login at IP address 10.1.10.1

Connect to your network:

Only if you use a computer already connected to your network, you can access the Router settings. This is why you will first connect to your network using either a wireless link if you are using your desktop, tablet or smartphone or a wired link while using your Computer or desktop.

Read More  192.168.100.1 - Router Network IP Address

Use your browser to navigate 10.1.10.1, to open the login tab.

To reach the Comcast Company Router login page you must use your browser. This is why you must enter the default 10.1.10.1 login IP in the Address bar or press 10.1.10.1.

Enter the Comcast Business router login details:

In this stage you will be required to type the username and password for the Comcast Business router login. If those details have not already been updated, using the default ones. If you changed them, please using the new password.

That login information can be found in the user manual or on the router. The default login information, however, are: If your wireless gateway’s default username and password is right you will be redirected to the router settings tab.

Now you can go through the menus and make the requisite modifications.

However, if you have changed the default configuration information of the Comcast Business router, you will need to reset the router to factory settings.

Frequently Asked Questions about 10.1.10.1 login:

How to find the default Wifi password?

Look at your Comcast Business Router at the bottom. Usually the default Wifi password and Network name (SSID) are printed on a label.

If you can’t connect to your Wifi network. What to do now?

Login to and disable your wireless gateway router as mentioned above and then enable the 2.4GHz and 5GHz Wifi network depending on which one you cannot link to.

Read More  10.0.0.1 - Router Network IP Address

How to change the Comcast Business router password?

Using 10.1.10.1 and default username and password to connect to the router, check the upper right corner of the screen and you will see Change Password. Only type in the default high-speed password, or you can’t access it, then enter your new password. You would need to type in the new password again before saving the changes.

How I can find out my router’s default login and passkey?

There are various conditions in there! All can forget password or username so certain methods are available to recover them. Firstly, test your system on all sides. If login and passkey stickers do not exist, you should search the guide book. You can search Default Router Passwords page on the website if nothing helps you.

If you have changed your password or passkey you can restore your router to default settings. It’s hard not. Special reset pushbutton has to be carried for around 20 seconds. After that, the identification details for your router will be restored to factory defaults.

Common issues during the use of 10.1.10.1:

10.1.10.1 isn’t working:

First, you need to make sure your gateway isn’t bridge mode. If it is then by default your access to the 10.1.10.1 IP will be deactivated.

Just in the event that you don’t use any of the Comcast Static IP on a Comcast gateway (CG) like SMCD#G, Netgear 3000 DCR or DPC3939B, you need to press the reset button for at least 15 seconds.

Read More  192.168.0.254 - Router Network IP Address

Your default parameters including entry to the 10.1.10.1 portal will now be reset.

10.1.10.1 timed out or refused to connect:

This is again an issue when your SMCD3G-CCR router is in bridge mode– this issue is also seen to occur. The easiest way to fix it is by resetting settings for the browser. A simple power cycle will put things back to function normal.

What should I do to set a port?

Typically, data is revised using special hardware and software, so you don’t have to do any ports behavior, but there are situations where you need to manually specify the number combination of ports: when you need to connect to a private server in the game.

When attempting to customize the program to Torrent.

To define applications that can be transferred through router?

If you need some camera link.

If you are using a special IP address that is used by network, device or software with its own port number, you can get permission. We can discuss security cameras, for example, that use IP address to offer access to someone who wants to use it.

Your camera has its own IP address and port, so you need to type IP address and port when you need to connect to your device.

Read More: 10001routernetworkipaddress
Related Search Terms:

  • 10.1.10.1
  • http 10.1-10.1 login
  • 10.1.10.1 login comcast
  • 10.1.10.1 login page
  • 10.1.10.1 router login
  • 10.1.10.1 xfinity

Conclusion:

There are Wi-Fi routers that have a few additional Internet links to customize and set preferences for use. This is better than just having two links.

Rate this post

Share This Post:

Twitter Facebook Pinterest LinkedIn

Filed Under: IP Address

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • 192.168.254.254 – Router Network IP Address
  • 192.168.100.1 – Router Network IP Address
  • 192.168.15.1 – Router Network IP Address
  • 192.168.10.1 – Router Network IP Address
  • 192.168.8.1 – Router Network IP Address

Categories

  • IP Address

Copyright © 2020 · PING IP ADDRESS